Bicycle Assembly

All Steady bicycle models arrive approximately 75% assembled in the box. Your Steady bicycle arrives in the box with the rear wheel, chain, and drive train already assembled and intact. The remainder of the bike that requires assembly is the front wheel, seat and seat post, pedals, reflectors, and a few other small items. For the Espresso Racer model, the front and rear brake cables must be inserted and adjusted. For most semi-mechanical customers, the final portion of a Steady bicycle’s assembly after being taken out of the box can usually be completed within about 30 to 45 minutes depending on your experience with bikes. For those who are mechanical or have experience assembling bicycles, the final assembly can be done in as little as 15 to 20 minutes on most models.

While many of our customers that purchase a Steady bicycle online can easily assemble the remaining parts of the bicycle themselves, we boldly inform all customers that it is easy to damage and strip certain nuts and bolts if assembled incorrectly, or by not using the proper tools. Most bicycle shops offer bicycle assembly and final prep for online purchased bicycles for a small fee. We highly encourage going this route to ensure your bicycle is assembled and prepped properly.

For safety and liability, we firmly inform customers that injury can occur when riding a bicycle that has not been properly assembled and prepped.

Additionally, if you have never worked on a bicycle before, you should take your new Steady bicycle to a bike shop and pay to have it assembled for you. Steady Bicycle Company does not warranty parts or components damaged from improper assembly or accidents while putting the bicycle together.

Below are the very few items and tools needed to unpack, assemble, and prep each Steady bicycle model:


I. THE STEADY CLASSIC:

Part 1.    Unboxing the Bike (Tools Needed):
               -Scissors (for cutting through protective wrapping and through zip ties).

Part 2.    Assembling the Bike Once it is out of the Box (Tools Needed):
               -15mm wrench (for the wheel lug nuts, pedals)
               -13mm wrench x two of them (to tighten seat onto the seat post)
               -6mm ALLAN WRENCH (to tighten handle bars and stem / neck)
               -5mm ALLAN WRENCH (to tighten the seat clamp)
               -Phillips screwdriver (for reflectors)

Part 3.    Inflating Tires:
               -Tire pump for inflating tires. (Tire pressure info / specs located on the sidewalls of the bicycle's tires. Special Note: We inform customers that inflating bicycle tires too quickly with too powerful of an air compressor can easily pop the bicycle’s inner tubes. Using a bicycle pump instead of an air compressor to inflate your bike's tires for the first time is highly recommended.)


Steady Bicycle Company - Cafe Racer Bikes and Motorcycles Steady Bicycle Company - Cafe Racer Bicycles and Mopeds Steady Bicycle Company - Cafe Racer Cycles and Scooters




II. STEADY ESPRESSO RACER:

Part 1.    Unboxing the Bike (Tools Needed):
               -Scissors (for cutting through protective wrapping and through zip ties).
               -Needle Nose Pliers and Wire Cutters (for adjusting and cutting the brake cables)

Part 2.    Assembling the Bike Once it is out of the Box (Tools Needed):
               -15mm wrench (for the wheel lug nuts, pedals)
               -13mm wrench x two of them (to tighten seat onto seat post)
               -6 mm ALLAN WRENCH (to tighten handle bars and stem / neck)
               -5 mm ALLAN WRENCH (to tighten the seat clamp)
               -Phillips screwdriver (for reflectors)

Part 3.    Inflating Tires:
               -Tire pump for inflating tires. (Tire pressure info / specs located on the sidewalls of the bicycle's tires. Special Note: We inform customers that inflating bicycle tires too quickly with too powerful of an air compressor can easily pop the bicycle’s inner tubes. Using a bicycle pump instead of an air compressor to inflate your bike's tires for the first time is highly recommended.)


Steady Bikes - Rat Rod Bikes Shop Store Sales Steady Bikes - Rat Rod Bicycles Dealer for Sale Steady Bikes - Rat Rod Cycles Dealers Shops Sales Stores




III. STEADY BISTRO RACER:

Part 1.    Unboxing the Bike (Tools Needed):
               -Scissors (for cutting through protective wrapping and through zip ties).

Part 2.    Assembling the Bike Once it is out of the Box (Tools Needed):
               -15mm wrench (for the wheel lug nuts, pedals)
               -13mm wrench x two of them (to tighten seat onto seat post)
               -6 mm ALLAN WRENCH (to tighten handle bars and stem / neck)
               -5 mm ALLAN WRENCH (to tighten the seat clamp)
               -Phillips screwdriver (for reflectors)

Part 3.    Inflating Tires:
               -Tire pump for inflating tires. (Tire pressure info / specs located on the sidewalls of the bicycle's tires. Special Note: We inform customers that inflating bicycle tires too quickly with too powerful of an air compressor can easily pop the bicycle’s inner tubes. Using a bicycle pump instead of an air compressor to inflate your bike's tires for the first time is highly recommended.)


Steady Bicycle Company Classic Retro Vintage Rockabilly Beach Cruisers Steady Bicycle Company Classic Rockabilly Cafe Racer Rat Rot Bike Store Steady Bicycle Company - Your one stop shop for Cafe Racer bicycles